Triacs. BT series E sensitive gate. GENERAL DESCRIPTION. QUICK REFERENCE DATA. Passivated, sensitive gate triacs in a. SYMBOL PARAMETER. BT/DG, Specifications: Triac Type: Standard ; Configuration: Single ; Voltage – Off State: V ; Current – On State (It (RMS)) (Max): 4A ; Voltage. BT Datasheet, BT 4A V TRIAC Datasheet, buy BT

Author: Shakak Grogami
Country: Luxembourg
Language: English (Spanish)
Genre: Life
Published (Last): 3 December 2007
Pages: 153
PDF File Size: 14.8 Mb
ePub File Size: 8.69 Mb
ISBN: 179-8-76177-896-2
Downloads: 28692
Price: Free* [*Free Regsitration Required]
Uploader: Nijas

For this to happen, the gate pin of the TRIAC should receive a voltage greater than the threshold gate voltage and should also get a current that is greater than gate trigger current.

The whole process is outlined in Figure 6. By putting a resistor or a small capacitor or both in parallel between these two terminals, the capacitive current generated during the transient flows out of the device without activating it.

Snubber circuits are also used to prevent premature triggering, caused for example by voltage spikes in the mains supply. As in the case of a triggering in quadrant III, this lowers the potential of the n-layer and turns on the PNP transistor formed by the n-layer and the two p-layers next to it.

There was a problem loading comments right now. East Dane Designer Men’s Fashion.

Amazon Drive Cloud storage from Amazon. Please enter a question. From Wikipedia, the free encyclopedia. You can read this article if you want to know more about the switching modes.

Figure 5 shows the triggering process. There was a problem filtering reviews right now. This switches on a structure ttriac by an NPN transistor and a PNP transistor, which has the gate as cathode the turn-on of this structure is indicated by “1” in the figure.

Customer reviews

Amazon Advertising Find, attract, and engage customers. Triggering in this quadrant is similar to triggering in quadrant III.

Other than controlling through switch the BT can also be controlled through a microcontroller or a microprocessor. This is because it is the only quadrant where gate current is injected directly into the base of one of the main device transistors.


Access Denied

However, the structure is different from SCRs. The lower p-layer works as the collector of this PNP transistor and has its voltage heightened: When switching on, the device starts to conduct current before the conduction finishes to spread across the entire junction.

This way the Load can not only be switched but also the output coltage can be controlled by using PWM signals for fast switching. Latching current is the minimum current that keeps the device internal structure latched in the absence of gate current.

Alexa Actionable Analytics for the Web. Quadrants, 1 top right2 top left3 bottom left4 bottom right. The product does not contain any of the restricted substances in concentrations and applications banned by the Directive, and for components, the product is capable of being worked on at the higher temperatures required by lead—free soldering The restricted substances and maximum allowed concentrations in the homogenous material are, by weight: Our website uses cookies and similar technologies to provide you with a better service while searching or placing an order, for analytical purposes and to personalise our advertising to you.

Views Read Edit View history. In particular, if the pulse width of the gate current is sufficiently large generally some tens of microsecondsthe TRIAC has completed the triggering process when the gate signal is discontinued and the latching current reaches a minimum level called holding current.

RS Components Statement of conformity. This page works best with JavaScript.

Because each SCR will have an entire half-cycle of reverse polarity voltage applied to it, turn-off of the Traic is assured, no matter what the character of the load. Because in the TRIAC there are parasitic resistances, a high reverse current in the p-n triaf inside it can provoke a voltage drop between the gate region and the MT1 region which may make the TRIAC stay turned on.

This, in turn, causes the p, n and p layers over MT2 to behave like a PNP transistor, which turns on because its n-type base becomes forward-biased with respect to its emitter MT2.


BTE TRIAC Pinout, Equivalent, Specifications & Datasheet

In these situations it is normal to connect the bt1136 terminal to the positive rail of the microcontroller’s power supply, together with A1 of the triac, with A2 connected to the live. The mechanism is illustrated in Figure 3. In most applications, the gate current comes from MT2, so quadrants 1 and 3 are the only operating modes both gate and MT2 positive or negative against Tria. Its formal name is bidirectional triode thyristor or bilateral triode thyristor.

Get fast answers from reviewers. Withoutabox Submit to Film Festivals. Generally, this quadrant is the most sensitive of the four. Amazon Restaurants Food delivery from local restaurants.

Top menu About Us Advertise. AmazonGlobal Ship Orders Internationally. Price Each In a Pack of A thyristor is analogous to a relay in that a small voltage and current can control a much larger voltage and current. In datasheets, the latching current is indicated as I Lwhile the holding current is indicated as I H. Amazon Renewed Refurbished products with a warranty. Retrieved from ” https: This page was last edited on 26 Julyat Complete Technical Details can be found in the datasheet present at the end of this page.

Add to Wish List. The reason is that during the commutation, the power dissipation is not uniformly distributed across the device. This in turn lowers the potential of the n-region, acting as the base of a pnp transistor which switches on turning the transistor on without directly lowering the base potential is called remote gate control. Therefore, the red arrow labeled with a “3” in Figure 6 shows the final conduction path of the current. English Choose a language for shopping.