PT2262 PDF

DESCRIPTION. PT is a remote control encoder paired with PT utilizing CMOS Technology. It encodes data and address pins into a serial coded. PT Datasheet, PT Remote Control Encoder Datasheet, buy PT Remote Control Encoder. A6/D5 ~ A11/D0. I. Code Address Pin Nos.6 ~ 11/Data Pin Nos.5 ~ 0. These six tri -state pins are detected by PT to determine the encoded waveform bit 6.

Author: Kajin Mezticage
Country: Costa Rica
Language: English (Spanish)
Genre: Literature
Published (Last): 16 November 2013
Pages: 34
PDF File Size: 2.55 Mb
ePub File Size: 13.83 Mb
ISBN: 316-3-94473-146-5
Downloads: 69479
Price: Free* [*Free Regsitration Required]
Uploader: Gabar

I made the resistors pullups so that the relays on our 4 channel relay module would be normally de-energised, forgetting how these module work! Yes you can change the address, there are a set of pads on the underside of the modules that allow you to easily jumper with solder the appropriate pins to VCC or VDD.

PT & PT Wireless Modules (HCMODU & HCMODU) –

There is one caveat that you can only pull one pin high at any one time. If the product uses a PT or 72 driver and operates on the same frequency then there is a chance but there are no guarantees. Even with only 1 channel tried all 4 separately connected on the TX all 4 channels on the RX change Hi to Lo when the switch is changed.

For the UK please choose the MHz version.

PT2262 DIP-18 PTC Remote Control Encoder GEN23

Is the address configurable on these modules? I bought 2 RX units and both do the same, but only 1 TX as that was all stock you had so not able to substitute that one. Can I use more than one transmitter on different addresses?

  KAFFEEPADAUTOMAT KM 42.17 PDF

We cannot guarantee compatibility with other third party products. You cannot have more than one PT module transmitting at the same time as they will interfere with each other, even if they are on different addresses. What does the DO do on the sensor? Comments made by this poster do not necessarily reflect the views of Ph2262 Components Ltd.

Only if you can control when a PT transmits so that no two PT modules transmit at the same time. All posts 1 pt222 7 days 2 weeks 1 month 3 months 6 months 1 year Sort by: It will then go back low when the button is released or the signal is interrupted in some way such as interference or going out of range.

I read that output type was momentary, and i need the remote circuit to mimic what happens at the tx switch end. They provide an easy way of remotely controlling up to 4 channels without the need of a microcontroller.

When purchasing these modules please ensure that match the correct frequency for your Tx and Rx pair and that the operating frequency is legal in your country. I’ll get the diagram updated as soon a possible. Can I use more than one receiver?

forum.hobbycomponents.com

No, you can only send DC logic levels with these modules. The are intended as a simple way to remotely trigger p2262 such as a garage door.

This makes them ideal for applications such as security systems, garage door controllers, home automation, and remote control. Yes, you can use as many receivers with one transmitter as you like. Will these modules do this? DC 5V Working Current: This works as expected so I know the RX circuit is wired correctly. Can I send serial data with these modules? The pins on the receiver will mimic the state of the pins on the transmitter.

  CALCULO DE ANCLAJES HILTI PDF

PT datasheet – PT is a Remote Control Encoder Paired With PT

You do not have the required permissions to view the files attached to this post. Can you switch the resistors and the switches around so that the resistors are pull-downs and the push buttons pull the pin up to 5V?

How do these modules work?

Edit That was it, swopped the connections round and its working correctly. Author Post time Subject Direction: There are 4 pins on the transmitter and 4 pins on the receiver. I can update the diagram tomorrow if you need to know how to do this. Board index Delete all board cookies Contact us. On the transmitter module you can then connect a relay to drive your pump to the corresponding output pin D0, D1, D2 or D3. Please note that we currently stock two versions of these modules operating p2262 or MHz.